Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
We've found this great article about How to Install a Bathtub Yourself down the page on the web and thought it made sense to share it with you over here.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old tub is easily obtainable, the job can move rapidly; if you have to open a wall surface to remove the old bathtub as well as place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the new one. Ensure you have qualified on your own for the work as well as fit trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This write-up will aid you set up a new tub in your bathroom if you have already acquired a brand-new tub and do not require to transform the setup of your previous water system pipelines.
Your tools and also product list should consist of the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing faucets can be fairly bothersome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the remaining water that will originate from the pipes. When the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before going on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of the two wooden boards under its feet, position the bathtub in the required position. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the bathtub till the level checks out level.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints as well as new pipework for leakages as well as tighten them if needed. Load the tub and additionally examine the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait until the bath tub has actually been made use of at the very least once as this will settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, bring about issues with moisture and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and fittings. They are marketed in tubes and also cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealant can break rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the floor tiles using waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that segment was sensible. I beg you take the opportunity to share this blog entry if you enjoyed reading it. Thank you so much for taking the time to read it.
High-quality repairs here. Report this page